| OCPP ChargeBoxIdentity (ChargePointID) |
IT*220*EPR000218 | The id that is sent to the backend and used by the backend to identify the charge point. |
| OCPP State (connector 1) |
IDLE (available) | State of OCPP at connector 1. |
| Type2 State (connector 1) |
(A) Vehicle not connected
PR: NO CABLE
Plug not locked | State of TYPE2 socket at connector 1. |
| Signaled current |
0 A | The current in Ampere that is signaled to the vehicle via PWM. |
| Connection Type (Backend) |
Ethernet OCPP-J 1.6 | The current connection type used for communication with the backend. |
| Connection State (Backend) |
CONNECTED (send HB in 42 seconds [interval:60]) | The current state of the backend connection on TCP level |
| Last backend error |
No error | The last reported backend error. |
| Connection State (Modem) |
Not installed | Show at which state in the connection sequence the modem is currently operating. Show OK when connected. Additionally APN session duration and traffic are shown. |
| Last connection failure (Modem) |
Not Available | Reason for the last modem APN connection failure |
| Free Charging |
Off | Shows if free charging is enabled and, if applicable, with which OCPP behavior it is configured. Note that in case of master slave scenario the slave will be automatically configured to the same mode the master uses |
| Errors list |
No errors | List of errors that are currently present in the charge point. |
| RCMB state |
RMS:OK DC:OK RCMB Device Status:OK
Last transaction maximum RMS: 0.9 mA DC: 0.1 mA
Values RMS: 0.0 mA DC: 0.0 mA | RCMB protection state
Maximum values of last transaction
Current values |
| OCPP URL of this ChargePoint (Standard OCPP) |
Not Available | The URL that the charger reports to the backend system. The backend system will use this URL to connect to the charger for any remote requests. |
| IMSI |
Not Available | The international mobile subscriber identity (IMSI), a value associated with the SIM card inserted into the built-in modem. If this number is properly read the SIM card is inserted correctly and can be read by the built-in modem. |
| IMEI |
Not Available | The international mobile equipment identification (IMEI). A number associated with the hardware of the built-in modem. If this number is present this device has a built-in modem and can properly communicate with the modem. |
| ICCID |
Not Available | The integrated circuit card identifier (ICCID) of the SIM card inserted into the built-in modem. |
| Requested Network operator |
| The name of the network operator to be used in manual mode. If operator name is unknown set the "Scan network operators at boot" parameter to On, then click on "Save & Restart". Then in the state page all the available operator names will be shown. |
| Currently used mobile network operator |
| The name of the network operator the built-in modem is currently connected to. |
| Available networks |
Not Available | The list of network operators that are available and visible using the current antenna. This value is only properly filled if requested using the "Scan network operators at boot" configuration parameter |
| Network registration mode |
Not Available | The current network registration mode of the modem which informs about the technology (2G, 3G, 4G) and about the registration (home network, roaming...) |
| Network registration state |
Not Available | The registration state to the mobile network. |
| Modem access technology |
Not Available | Shows which access technology (2G, 3G, 4G) the modem is currently using. |
| Scan network operators at boot |
Off | Determines whether upon boot a search for available network operators is carried out. The result can then be requested as separate parameter. The value is automatically set to off after boot. |
| Operator Selection Mode |
Not Available | Operator Selection Mode, Auto or Manual... |
| Cell id |
Not Available | Cell Id as reported by the built-in modem, this value can be used to determine the finer location of the charge point |
| Additional modem information |
Not available | Shows the modem manufacturer, model and firmware revision. |
| Backend uptime |
07:23:21:30
| Backend uptime (d:h:m:s) |
| List of interfaces |
eth0: [00:71:00:FF:27:98] IP: 192.168.0.100 (ocpp) | List of interfaces and their IPs |
| Meter configuration (OCPP) |
Internal Meter | The type of meter used for the charging socket and its connector. This is relevant for OCPP transactions. |
| Meter serial number (OCPP) |
No Id read yet | Serial number as reported by the eHZ or ModBus meter |
| Meter public key (OCPP) |
Not Available | Public Key of the cryptography engine of the connected eHZ meter if available |
| Energy in Wh (OCPP) |
Total: 85281 [Wh] ( 82313 | 342 | 2627 ) [Wh] | Computed energy consumption in Wh. |
| Power in Watt (OCPP) |
Total: 0 [W] ( 0 | 0 | 0 ) [W] | Computed power consumption in Watt from OCPP meter |
| Current in A (OCPP) |
( 0.00 | 0.00 | 0.00 ) [A] | Phases Current in Ampere measured by ocpp meter |
| Meter configuration (Second) |
No Meter | Energy Management: the type of second meter, used only for input to manage the current on the grid. |
| Energy Manager Main State |
25 A | Energy manager module's state and current |
| Temperature Monitoring State |
32 A (Ambient temp: +4.50 C) | Temperature monitoring module's state and current |
| Second Meter State |
32 A (Disabled) | Second Meter module's state and current |
| External Input State |
32 A (Disabled) | External Input module's state and current |
| Relays Temperature State |
32 A | Relays Temperature module's state and current |
| OCPP Smart Charging State |
32 A | OCPP Smart Charging module's state and current |
| Operator Current Limit |
25 A | Current limit in Ampere set by the operator |
| DLM Current Applied |
0 A (Disabled) | Available Charging Current assigned by DLM Master |
| Eichrecht State |
32 A | Eichrecht module's state and current |